DRD Team

Well i´ve noted some anomaly in a sector with transfers brightness level, sprites works fine, but the models, they got almost black! (like if i saw it in a place with brightness 26), they works fine with places without transfer brightness.

Fog tested:off,standard, radial, they got the same result.

One strange thing is the weapons in 3D didn´t get the same result, it works fine, here´s a picture with a demon from doom 3 with a demon from doom 1/2, this time i tested in another computer and get the same result.


Sorry I could only test in skulltag because hunters moon don´t work in gzdoom, I´m downloading DS-MODELS for test in gzdoom, but i except the same result.

Like enjay wrote to me...

Hardware
Intel Pentium III 1GHz
896mb SDRAM
Nvidia FX5500 AGP2X
120GB HD
Via Appolo A133 chipset (sucks)
Latest gzdoom (i think from December 14, 2010)

EDIT:Tested in Gzdoom and got a fatal error with or without models =/, only worked in skulltag and zdoom
Tomorrow i can do more tests...

Upload a test WAD with the models for a quicker response.

ibm5155 wrote:Latest gzdoom (i think from December 14, 2010)

Try an SVN build instead.

ibm5155 wrote:EDIT:Tested in Gzdoom and got a fatal error with or without models =/, only worked in skulltag and zdoom

Yeah, that's a bit meaningless to me. Skulltag is closed source, ZDoom does not support models at all.

Nash wrote:Upload a test WAD with the models for a quicker response.

Dunno about Graf, but personally I won't even try to investigate without one.

Im going to host the map...
@Gez, gzdoom also crashed without models, and this map is compatible with the future zdoom so...


I´ve tested with hunters moon v1.6 and DS-models (i only have demons/revenants in that part), you could use anything together for replace it by 3D models =D

About my gzdoom
Gzdoom 1.5.6 r1104 (yeah the last one that´s in the download page)

Yes, I can reproduce in with GZDoom r1280 with the test map and Hunter's Moon loaded.





I'm also pretty sure I know what is causing the problem. The map uses the transfer brightness special to have the room getting progressively darker the higher up you go. The main play area is set to quite a low light level and has its brightness at ground level increased by the transfer brightness special.

However, it is known that models do not use "3D lighting" effects (including the lighting effect from being underneath a 3D floor and the situation in this map) and will use the light level of the main sector regardless of the 3D lighting effect being used at the altitude the model is at. A quick way to test is to force X/Y billboarding on all sprites and then see what happens. In that mode, sprites also can not use 3D lighting effects.

X/Y billboarding off



X/Y billboarding on



So, there you have it. It's not a bug but I wouldn't go as far to call it feature. I suppose it's merely a known about limitation.

I guess the solution for this map is to make the main play sector the brightness that you want the models to be lit by and use the 3D lighting effects to change the light levels at heights where the monsters don't go.

? But the eye candy is normal o_O

ibm5155 wrote:? But the eye candy is normal o_O

Correct. It is a bright sprite so it is always shown at full brightness regardless of the sector it is in. Only non-bright sprites (ie ones that use the sector light level) will show this.

Ok, well i repaired the problem like enjay told to do, so it´s not really a bug, only a limitation on the engine >>
Cost me one minute to repair the sector >.<

Sorry doulbe post, the complete map is giving me crash only in gzdoom, i put the log without models

Your crash report says:
ZDoom version 1.5.6 (r1104) / ZDoom 2.5.0 (r3010) (Nov 20 2010)

What happens if you run it with one of the SVN builds from here?

http://svn.drdteam.org/gzdoom/

I´ve download the gzdoom-r1280.7z and now it works =D

Enjay wrote: However, it is known that models do not use "3D lighting" effects (including the lighting effect from being underneath a 3D floor and the situation in this map) and will use the light level of the main sector regardless of the 3D lighting effect being used at the altitude the model is at. A quick way to test is to force X/Y billboarding on all sprites and then see what happens. In that mode, sprites also can not use 3D lighting effects.

That's one of the ugliest limitations I've read about. Why are 3d models AND XY sprites exempted from 3D lighting? This is a 3d engine! It makes the 3d wall-lighting feature seem rather broken if it can't be used to properly light half of the objects in sight and at the corresponding heights.

Because these things can't be trivially split into slices to be lit indepently.

Can they be lit uniformly, but only by the light level that their origin resides in?

That's how it should be - but some other people have also messed around with that code so it may just be broken.